Siser EasyWeed Adhesive 11.8" Roll (Yard) **FREE SHIPPING**

Description

EasyWeed® Adhesive
Create Shining Decorations For Less!
EasyWeed Adhesive lets you create a trendy style without breaking the bank. Compatible with cost effective screen printing foils, this adhesive is a money saver and a money maker!  In addition to screen print foils, EasyWeed Adhesive is compatible with fabrics and other materials that lend themselves to adhesion. The milky colored adhesive shares benefits of EasyWeed such as a pressure sensitive carrier and low application temperature. Therefore, the standard cutting process for cuttable materials is used when working with EasyWeed Adhesive. Weeding on a dark surface will provide the best visibility.
EasyWeed Adhesive is
CPSIA Certified
so it’s it’s safe on garments for all ages!.
Specifications: PET Composition • Pressure sensitive backing • Semi-gloss finish • 75 Microns/2.95 Mils • 45°/60° blade • Should be Layered
Cutter Setting
Cricut®
Silhouette Cameo
Scan N Cut
Roland GS/GX-24
Graphtec
Blade: Standard
Setting: Iron- On
Blade: Standard, 3
Setting: Heat Transfer
Material: smooth
Speed: 8
Force: 6
Blade: Standard,2
Cut Speed: 1
Cut Pressure: 1
Blade: 45°
Gram Force: 80-90
Offset: .250
Speed: 25-50 cm/s
Blade: 45°
Gram Force: 9-10
Tool: CB09U+0
Speed: 30 cm/s
Application Instructions
Application instructions ( home iron )
Application Instructions ( heat press )
- Set iron dial between Cotton and Linen.
- Cover design with Kraft paper or non-stick cover sheet.
- Place on flat, hard surface (ironing board not recommended).
- Press iron with medium/firm pressure (do not slide iron).
- Press each section of design for 10-15 seconds.
- If areas of design lift after application, replace cover sheet and re-press for
5 seconds.
- Peel carrier hot
- Cut in Reverse.
- Weed excess material.
- Preheat garment for 2-3 seconds.
- Apply design at 275°F/135°C.
- Use firm pressure for 5-10 seconds.
- Peel carrier hot
Recommended Accessories & Care
Easyweed Adhesive Applies to
Recommended Accessories
Laundering
100% cotton
100% polyester
Poly/cotton blends
Siser Weeder
Multipurpose Paper or
Kraft Paper or Heat Transfer
Cover Sheet
Wait 24 hours before 1st wash
Machine wash cold / mild detergent
Dry on normal dryer setting
Do not dry clean
How to Cut and Heat Apply EasyWeed Adhesive HTV
If you look for the sunshine through the clouds you’ll likely find the bright side! If you apply EasyWeed Adhesive HTV to your project, you may find it too! The          cloudy appearance of EasyWeed Adhesive turns clear when applied and becomes bright like the sun when you add a screen printing foil on top. Here’s how          you can make shining shirts with EasyWeed Adhesive:
Just like the materials in the EasyWeed Family, EasyWeed Adhesive HTV has a carrier side and a material side. The carrier side is noticeably smoother and         shinier than the material side. Now you may notice the material side looks like it doesn’t have any, well, material. That’s because it’s simply a layer of mostly           transparent glue. Not just any glue though, EasyWeed Adhesive HTV! EasyWeed Adhesive can not only be used with screen printing foils, it also works with           fabrics and other materials that lend themselves to adhesion.
EasyWeed Adhesive can be cut on any vinyl cutter and requires the typical steps before cutting Siser heat transfer vinyl. Make sure to mirror your design and         place the carrier side face down on the cutting mat. Then make sure you pin the image below so you can always find your cut settings! I always recommend a       test cut before cutting a full design. How old your blade is and how used loved it is will effect your blade and cut settings, so make sure your blade produces a       good cut with our suggested settings or make some adjustments.
1. Place material with carrier side face down on cutting mat.
2.Load material into cutter and do a test cut.
If you’re using a large format cutter, like the Roland GX24, you’re cut settings will be GF: 80-90, Offset: .250, CM/S: 30 with a 45° blade. If you’re using a 60° blade, the settings are the same except the offset is changed to 3.50.
When it comes to weeding EasyWeed Adhesive HTV you may drive yourself crazy trying to weed it on top of a light colored surface. Instead, weed on top of a dark table or place a dark piece of paper or fabric behind the material so you can identify the cut lines.
Start by weeding the outside of the material by hooking your Siser Weeder into a corner and separating the excess material from the carrier.
We wouldn’t call it EasyWeed Adhesive for nothing. This material weeds simply like any other EasyWeed material!
Once you can see the design of your outline, weed out any cavities in the design.
When I think I’ve got all my excess adhesive removed I like to flip my design over and inspect it from the carrier side to make sure I really got it all.
When your certain it’s weeded perfectly you can prepare to heat apply! Heat Press Settings for EasyWeed Adhesive HTV are: Temperature: 275°F/135°C, Pressure: Medium. Start by preheating your garment for 2-3 seconds so you have a wrinkle and moisture free area to apply to.
Place the adhesive with the carrier side face up, cover with a heat transfer cover sheet, and press for 5 seconds. Leave the garment on the heat press and peel the carrier hot. You’ll notice the shiny, clear adhesive is left behind.
Now you’ll add the top layer material. In this case it’s a screen printing foil. Cut a piece large enough to cover your design. Place the piece on top of the EasyWeed Adhesive with the color side up.
Recover with your heat transfer cover sheet and press for 10 seconds. Notice how the adhesive has gripped the foil.
Before excitedly peeling off the foil, remove the garment from the heat press and wait until the foil is cool to the touch. Your patience will be rewarded with a shiny, super cool garment!
You may notice small gaps in the foil on your garment, that’s because screen printing foils don’t actually offer full coverage. It’s normal for small pieces to get left behind on the foil sheet.
This gives the foil a bit of a distressed look that’s very popular. If you want an even more distressed look, crumple the foil before heat application.
Payment
Shipping
Same Day or 1 day Shipping for orders placed
before 3:00 PM (Monday-Friday)
2-4 business day transit time.
See map above
Payment and Return/Exchange
Change pick up hours to Monday-Friday 8:00-4:00.
Same day pick up as long as order is placed
before 3:00 PM.
Please bring valid ID and invoice.